Other indicators like Universe color are displayed to show the custom universe color which is set in the TimoTwo module when in transmitter mode. LED’s for wireless signal strength, RDM/DMX data and status are helpful for quick diagnostics. Full radio and system status LED’s makes trouble shooting easyĪ quick glance at the LED panel lets you know right away what’s happening with the radio. DMX Workshop which is a free app available from Artistic License, can be used to control and change RDM settings for both the embedded TimoTwo module and the FivePiece controller. Channel settings, trigger sensitivity, hold, fade and much more are all available through RDM software commands. The FivePiece controller is fully RDM compliant and supports many RDM commands. No more getting up and going to the device to change the DMX address or any control settings. The Lighting operator could then use their iPad device to control all mobile performers as individual DMX fixtures. A good example of this would be a marching band that has BrightBeats WMobile wireless controllers on each drum linked back to a FivePiece controller at the control area. In Transmitter mode other CRMX wireless fixtures can be linked to the FivePiece controller and then utilizing the built in Bluetooth radio, an iPad could be used to run DMX lighting software to control all linked devices. The FivePiece controller can be operated as a wireless CRMX receiver or can be switched into a wireless CRMX transmitter via the LumenRadio CRMX app. It even works with the wired nic disabled and the ip address of the wireless set to 2.0.0.Description Our latest and most advanced wireless design yet!īased on the Lumen Radio TimoTwo CRMX wireless module. This keeps working even with the windows firewall and the wireless connection active and a loopback connector connected to the wired nic. I also tried anothe Art-Net listener being the Luminex Wygalizer (whitch is probably not as strict) that interfaces with Wysiwyg visualization software and this works perfectly providing I start FS first and than the Wygalizer. Now I am wondering could it be that the Art-Net tool must be on a different pc? I have not yet tried this, since right now I only have 1 pc (expecting to get one in a couple of months) I have the windows firewall running (turning it on or off did not change anything in the above behavior)ĭisabling my wireless connection also did not change the above behavior. (although it did the same with an ethernet loopback connector) I have it all running on one laptop (win xp) with 2 network interfaces: one wireless (that connects to my wireless router at a local ip address) and one wired, which I also connected to my router and gave a fiwed ip address of 2.0.0.1. If you then start up FS, the latter just does not send anny packet at all. If you do it the other way around and start up the Art-Net to DMX tool first, that one starts up ok. If you then start the Art-Net to DMX tool, the latter gives an error saying: Address 0 in use and when you click ok, it says: Interface error I figured out that when you start FS (with the Art-net interface selected) it starts sending out Art-Net packets. I have did som more tries and used an ethernet packet sniffer and got it (partionally) working. I have checked the blackout and freeze settings and also the master (whitch is at 100%). It seems reestyler is not sending out any Art-Net packet. I think my network setup is ok, because when I start Dmx Workshop (from Artistic License) I can change the output values in Art-net to DMX tool perfectly. When I open the edit/Show Output I get a window with 6 output values that are responding to the sliders on the right of Freestyler, but the Art-Net outputs remain at zero. When I open the Art-Net to DMX tool, It says:īut when I open the show output dialog, the values stay at zero. I use a 6-bar of PAR64's starting at dmx address 1. I have chosen the Art-Net interface with universe 0 in the Freestyler setup. I have my laptop connected to a network router and my nic's IP address is 2.0.0.1 subnet mask: 255.0.0.0 I am trying to set up Freestyler to run on Art-Net interface, but it does not seem to work. I am new to Freestyler so maybe my problem is trivial but annyway.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |